
AI Computing
Lesson Content
Maintenance and Calibration
Daily Operations
System Health Monitoring
Critical Parameters to Monitor:
-
Temperature Monitoring
- Mixing chamber: 10-20 mK
- Each stage temperature
- Rate of temperature change
- Alert if > 50 mK
-
Pressure Systems
- Helium circulation pressure
- Vacuum chamber pressure (< 10⁻⁶ mbar)
- Leak detection
-
Qubit Performance
- T1 (relaxation time)
- T2 (dephasing time)
- Gate fidelity
- Readout fidelity
Monitoring Dashboard Example
code# Typical monitoring script import monitoring_api status = monitoring_api.get_system_status() if status['temp_mixing_chamber'] > 0.050: # 50 mK alert('Temperature too high!') if status['qubit_t1'] < 50: # microseconds alert('Qubit coherence degraded') if status['gate_fidelity'] < 0.99: schedule_calibration()
Calibration Procedures
Automated Daily Calibration
Typical calibration routine (2-4 hours):
-
Qubit Frequency Calibration
- Sweep microwave frequency
- Find resonance peak
- Update frequency parameters
- Time: ~5 minutes per qubit
-
Gate Calibration
- Single-qubit gate optimization
- Two-qubit gate tuning
- Minimize gate errors
- Time: ~30 minutes per gate
-
Readout Calibration
- Optimize measurement pulses
- Discriminate |0⟩ and |1⟩ states
- Minimize readout errors
- Time: ~10 minutes per qubit
-
Crosstalk Calibration
- Measure unwanted interactions
- Adjust isolation parameters
- Update crosstalk matrix
Manual Calibration Tasks
Weekly Procedures:
- Flux bias optimization
- Coupler calibration
- Amplitude calibration
- Phase calibration
- Cross-resonance gate tuning
Monthly Procedures:
- Full system characterization
- Randomized benchmarking
- Quantum volume measurement
- Update error mitigation matrices
Preventive Maintenance
Cryogenic System
Weekly:
- Check helium levels
- Inspect for frost/ice buildup
- Verify vacuum seals
- Check pump oil levels
- Monitor vibration levels
Monthly:
- Helium recovery system check
- Replace filters
- Lubricate pump bearings
- Calibrate temperature sensors
Quarterly:
- Full system inspection
- Replace consumables
- Update firmware
- Pressure test
Electronics Maintenance
Daily:
- Check signal quality
- Monitor amplifier temperatures
- Verify lock status
- Check error logs
Weekly:
- Recalibrate mixers
- Check cable connections
- Update lookup tables
- Backup configuration
Monthly:
- Replace failing components
- Update software
- Network security patches
- Archive calibration data
Common Issues and Troubleshooting
Issue 1: Degraded Qubit Coherence
Symptoms:
- T1/T2 times decreased
- Gate fidelity below threshold
- Increased error rates
Diagnostic Steps:
- Check temperature stability
- Verify no new noise sources
- Check for magnetic field changes
- Inspect signal quality
Solutions:
- Recalibrate qubit parameters
- Adjust flux bias
- Improve shielding
- Replace faulty components
Issue 2: Temperature Fluctuations
Symptoms:
- Mixing chamber temp > 50 mK
- Unstable qubit frequencies
- Poor gate performance
Diagnostic Steps:
- Check helium flow
- Inspect for leaks
- Verify pump operation
- Check heat load on cables
Solutions:
- Adjust circulation rate
- Repair leaks
- Service pumps
- Add attenuation
Issue 3: Readout Errors
Symptoms:
- State discrimination < 95%
- Inconsistent measurements
- Calibration drift
Diagnostic Steps:
- Measure IQ cloud separation
- Check amplifier gain
- Verify timing synchronization
- Test discriminator threshold
Solutions:
- Recalibrate readout
- Adjust amplifier settings
- Retrain classifier
- Replace amplifier if needed
Helium Management
Helium-3 System
Inventory Tracking:
- Helium-3 is rare and expensive ($~2000/liter)
- Monitor circulation efficiency
- Track losses
- Schedule recovery maintenance
Recovery System:
- Captures boil-off gas
- Liquefies for reuse
- Reduces operating costs
- Requires regular maintenance
Refilling Procedures
Helium-4 Refill (Every 1-2 weeks):
- Monitor level sensors
- Calculate transfer amount
- Connect transfer line
- Monitor during fill
- Verify final level
Helium-3 Charge (Annual):
- Warm up system
- Evacuate lines
- Transfer from storage
- Cool down (24-48 hours)
- Verify circulation
Software Maintenance
Control Software Updates
Version Control:
code# Update control software git pull origin main pip install -r requirements.txt --upgrade # Run regression tests pytest tests/calibration/ pytest tests/gates/ # Deploy to production ansible-playbook deploy.yml
Update Schedule:
- Security patches: Immediate
- Bug fixes: Weekly
- Feature updates: Monthly
- Major versions: Quarterly
Data Management
Backup Strategy:
- Calibration data: Daily
- Experimental results: Real-time
- System logs: Continuous
- Configuration: On change
Storage Requirements:
- ~1 TB per month typical
- Compressed archive storage
- Redundant backups
- Cloud sync optional
Performance Metrics
Key Performance Indicators
System Uptime:
- Target: > 95% availability
- Track downtime causes
- Planned maintenance windows
Qubit Metrics:
- T1: > 100 μs target
- T2: > 50 μs target
- Gate fidelity: > 99%
- Readout fidelity: > 95%
Calibration Drift:
- Frequency drift: < 100 kHz/day
- Gate drift: < 0.5%/day
- Readout drift: < 1%/day
Reporting
Daily Report:
- System status
- Calibration results
- Error budget
- Issues encountered
Weekly Report:
- Performance trends
- Maintenance activities
- Upgrade recommendations
Monthly Report:
- Uptime statistics
- Benchmark results
- Costs analysis
- Improvement plans